Podwójna obudowa na HDD/SSD 2,5"/3,5" RAID 1 w 2x zatoce 5,25"
Galeria
WYJMOWANE OBUDOWY NA DYSK TWARDY 3,5"
Coming Soon!

FatCage MB901SPR-B to podwójna stacja RAID mieszcząca dwa dyski 2,5/3,5" SATA w dwóch zatokach 5,25". Dzięki wbudowanemu kontrolerowi RAID 1 możesz z łatwością zadbać o ochronę twoich danych dzięki kopii lustrzanej. MB901SPR-B zarządza macierzą bez tworzenia narzutu obliczeniowego na procesor hosta ograniczając zużycie zasobów systemowych, tym samym stanowiąc doskonały wybór wszędzie tam, gdzie liczy się zachowanie ciągłości pracy oraz bezpieczeństwo danych.
 
 
Wbudowany kontroler RAID 1
Dzięki wbudowanemu układowi JMS562 możesz z łatwością stworzyć macierz dyskową z dwóch nośników HDD/SSD bez potrzeby użycia dodatkowych kontrolerów. Duplikacja danych odbywa się automatycznie, stanowi zabezpieczenie przed przestojami w pracy i utratą danych wynikłą z uszkodzenia pojedynczego dysku.
 
 
Zaawansowane wskaźniki stanu dysków

FatCage RAID MB901SPR-B wyposażony jest w czytelne wskaźniki stanów zainstalowanych nośników - monitorują one parametry oraz poprawność obu dysków z osobna. Odczyt stanu macierzy możliwy jest również z pomocą dedykowanej aplikacji.

Uwaga: opcjonalne oprogramowanie monitora RAID jest dostępne do pobrania [tutaj] . Wspiera zarówno Windows oraz Mac.

 
 
System uniwersalnych tacek
 
 
FatCage Raid korzysta z przenośnych tacek wspólnych dla innych produktów z serii FatCage/DataCage umożliwiając przenoszenie i wymianę dysków bez konieczności otwierania obudowy komputera czy jego wyłączania. Dzięki unikalnej konstrukcji tacki są kompatybilne z dyskami 3,5" oraz 2,5".
 
 
 
Uziemienie EMI
Zabezpieczenie dysków przed destrukcyjnym działaniem ładunków elektrostatycznych jest szczególnie kluczowa, zwłaszcza tam gdzie dochodzi do częstych wymian pracujących nośników. Nasza technologia uziemienia pozwala na pełną ochronę twoich danych oraz sprzętu.
 
 
Przemyślany design
Duże otwory wentylacyjne umożliwiają pasywne odprowadzanie ciepła z pracujących dysków pozytywnie wpływając na ich żywotność
 
FatCage RAID MB901SPR-B wspiera 15-pinowe złącza sata z zatrzaskiem uniemożliwiającym samoczynne rozpięcie się kabli.
Kluczowe cechy
 
*
Wspiera 2 dyski 2,5"/3,5" SATA HDD/SSD
*
Instalacja w podwójnej zatoce 5,25"
*
Transfer danych do 6 Gbps
*
Wbudowany układ RAID1 JMS562
*
Czytelne wskaźniki stanu informujące również o awarii dysku i procesie odbudowy macierzy
*
Technologia antywibracyjna (AVT)
* Aktywne zarządzanie energią (APT) - wyłączenie kontrolera gdy nie są zainstalowane żadne dyski
*
3 letnia gwarancja
 
 
3 Years Warranty

Model Number :
MB901SPR-B
Color :
Black + Silver
Support Drive Size :
2 x 2.5”/3.5” SSD/HDD
Compatible Drive Type :
SATA
Number of Drives :
2
Max Drive Height :

2.5" HDD/SSD up to 15mm height
3.5" HDD up to 26.1mm height

Drive Bay :
2 x external 5.25" drive bay
Host Interface :
1 x SATA 7pin
Power Input :
2 x 15pin SATA power connector
Transfer Rate :
Up to 6G/bs. (Depending on hard drive speed)   
Support HDD Capacity :
No Limitation
Drive Cooling :
Metal heat dispersion
Support Hot-Swap :
Yes
RAID Function :
RAID 1 (SAFE)
Controller IC :
JMicron – JMS562
Structure / Material :
Metal with partial plastic ABS
Dimension (W x H x L) :
146.4 x 85.8 x 200.4mm
Product Net Weight:
1,052g
Package Gross Weight:
1,360.1g
Supported Operating:
Windows 10, 8.1, 8, 7 and Vista
RAID 1 Status LED Indicator:

RAID 1 configuration is normal: solid green Degraded RAID 1: LED off

Rebuilding Progress LED Indicator:
Divide the progress into four stages: Flashing green
HDD Fail LED Indicator:

HDD fail: solid red in corresponded device slot
Double source: solid red in both device slots
Capacity error: Solid red in the device slot which has smaller capacity drive

Double Source LED Indicator:
Double source: solid red
Capacity Error LED Indicator:
Capacity error: solid red
Drive Activity LED Indication:

Empty bay: LED off
Drive power: solid green
HDD fail: solid red
HDD access: flashing green

Package contents:
Device, User Manual, Screws
SATA Connector Insertion Rate:
10,000
Humidity:
5%~65% RH
Operating Temperature:
0°C to 60°C (32°F to 140°F)
Storage Temperature:
-35°C to 70°C (-31°F to 158°F)
Compliance:
CE, RoHS, REACH
Warranty:
3 years

Documents
 

 

 

Frequent Asked Questions
 

Q: What is RAID and what are different mode?

Note: Not all ICY DOCK enclosure support each of the RAID modes described below. For more information on the RAID modes that your enclosure supports, refer to the manual or the icydock.com product page.

Redundant Array of Independent Disks (RAID) is a virtual disk technology that combines multiple physical drives into one unit. RAID can create redundancy, improve performance, or do both.

RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, it should be backed up to another physical drive or logical set of drives.

 

The following are terms that normally used in connection with RAID:

• Striping: data is split between multiple disks.
• Mirroring: data is mirrored between multiple disks.
• Parity: also referred to as a checksum. Parity is a calculated value used to mathematically rebuild data.
Different RAID levels exist for different application requirements.


Refer to the following table for the list of RAID modes offered by some ICY DOCK products:
RAID MODE Description Operation Advantages Disadvantages Recovery
RAID 0 Striped disks Data is split evenly between two or more disks. Large size and the fastest speed. No redundancy. If one or more drives fails, this results in array failure.
RAID 1 Mirrored disks Two drives have identical data on them. A single drive failure will not result in data loss. Speed and size is limited by the slowest and smallest disk. Only one drive is needed for recovery.
JBOD Just a Bunch Of Disks Any number of drives are accessed independently by the operating system. Software RAID modes can be used. Hardware RAID may have better performance. N/A
BIG Spanning or Concatenation Data is written on one drive until it is full, and then the next drive(s) until it or they are full. Creates a very large and simple array. No redundancy. N/A

Q: How do I rebuild my RAID 1 array?

1. Determine which drive is operational by using the RAID monitoring software (if available) or test each drive individually on a different hard drive enclosure or by connecting each drive directly to a computer’s SATA port.
2. Replace the failed drive with an identical hard drive.
3. The array will rebuild and is accessible during the rebuilding process.
 

Note 1: It is recommended to use a new identical hard drive for the rebuild. To use a used drive, we recommend use Window’s DiskPart command to clean and format the used hard drive before you start rebuilding.

Note 2: Before you start the rebuilding process, make sure the replacement drive has no previous RAID table in it.


Q: My computer is only recognizing one of the hard drives while using SATA/eSATA. What do I do?

SATA hard drive controllers require a feature called port multiplier to read more than one hard drive per SATA or eSATA port. The port multiplier feature is not standard on many SATA hard drive controllers.
If your computer is only recognizing one of your hard drives, you need to plug the SATA/eSATA cable into a SATA controller that includes the port multiplier feature. If none of your current hard drive controllers include this feature, you can add a hard drive controller that does support port multiplier in any available expansion slot (for example, PCI, PCI-Express, PCMCIA, CardBus, or ExpressCard).

If you have a hard drive controller card that does support the port multiplier feature but it is only reading one hard drive at a time, update the drivers of the hard drive controller.


Q: Everything is connected, but nothing is working. What do I do?

When you troubleshoot issues with a hard drive enclosure, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
• Cables (USB, SATA, SAS, Mini-SAS, etc)
• Hard drives / SSD (M.2 drive, 3.5'' hard drive, solid state drive, etc)
• Hard drive enclosure (converter, mobile rack, cage, and external enclosure)
 
To test your setup components, try the following:
• Connect the hard drive directly to the system or use the hard drive in another enclosure to see if the problem is with the hard drive.
• Use the cables, hard drives, and hard drive enclosure in another setup to see if the problem is with the components or the setup.
• Use a different cable, hard drive, and hard drive enclosure in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.
 
When you test the hard drive and hard drive enclosure, it is recommended that you do the following:
• To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
• If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.
 
Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.
• If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.
 
Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.
 
For additional help with setting ICY DOCK RAID enclosure, please contact us by email, phone, or live chat.